[Dec 14, 2025] Reliable FCP_FAZ_AD-7.4 Exam Tips Test Pdf Exam Material
New 2025 FCP_FAZ_AD-7.4 Test Tutorial (Updated 185 Questions)
Fortinet FCP_FAZ_AD-7.4 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
NEW QUESTION # 101
On the RAID management page, the disk status is listed as Initializing.
What does the status Initializing indicate about what the FortiAnalyzer is currently doing?
- A. FortiAnalyzer is functioning normally
- B. FortiAnalyzer is writing data to a newly added hard drive to restore it to an optimal state
- C. FortiAnalyzer is writing to all of its hard drives to make the array fault tolerant
- D. FortiAnalyzer is ensuring that the parity data of a redundant drive is valid
Answer: C
Explanation:
Reference: https://fortinetweb.s3.amazonaws.com/docs.fortinet.com/v2/attachments/4cb0dce6-dbef-11e9-
8977-00505692583a/FortiAnalyzer-5.6.10-Administration-Guide.pdf (40)
NEW QUESTION # 102
Which statement correctly describes RAID 10 (1+0) on FortiAnalyzer?
- A. A configuration with four disks, each with 2 TB of capacity, provides a total space of 2 TB.
- B. It uses striping to provide performance and fault tolerance.
- C. 11 combines mirroring striping and distributed parity to provide performance and fault tolerance
- D. A configuration with four disks, each with 2 TB of capacity, provides a total space of 4 TB.
Answer: D
Explanation:
RAID 10 combines mirroring (RAID 1) and striping (RAID 0). In a RAID 10 setup with four disks, data is mirrored across two pairs of disks, and those pairs are striped for performance. This results in improved performance and fault tolerance, but the total usable storage is 50% of the total raw storage, meaning four 2 TB disks provide 4 TB of usable space.
NEW QUESTION # 103
Which SQL query is in the correct order to query the database in the FortiAnslyzer?
- A. FROM Slog WHERE 'user* =' USERl' SELECT devid GROUP BY devid
- B. SELECT devid FROM Slog GROOP BY devid WHERE * user' =* USERl'
- C. SELECT devid FROM Slog- WHERE *user' =' USERl' GROUP BY devid
- D. SELECT devid WHERE 'u3er'='USERl' FROM $ log GROUP BY devid
Answer: C
Explanation:
FortiAnalyzer_7.0_Study_Guide-Online.pdf page 259: The main clauses FortiAnalyzer reports use are as follows:
* FROM
* WHERE
* GROUP BY
* ORDER BY
* LIMIT
* OFFSET
Accordingly, following the SELECT keyword, the statement must be followed by one or more clauses in the order in which they appear in the table shown on this slide.
NEW QUESTION # 104
What does the disk status Degraded mean for RAID management?
- A. The FortiAnalyzer device is writing data to a newly added hard drive in order to restore the hard drive to an optimal state.
- B. One or more drives are missing from the FortiAnalyzer unit. The drive is no longer available to the operating system.
- C. The hard driveiIs no longer being used by the RAID controller
- D. The FortiAnalyzer device is writing to all the hard drives on the device in order to make the array fault tolerant.
Answer: C
NEW QUESTION # 105
Which process is responsible for enforcing the archive file size?
- A. logfiled
- B. sqlplugind
- C. miglogd
- D. oftpd
Answer: D
NEW QUESTION # 106
Which tabs do not appear when FortiAnalyzer is operating in Collector mode?
- A. Reporting
- B. Device Manger
- C. FortiView
- D. Event Management
Answer: D
NEW QUESTION # 107
What is the purpose of using prefilters when configuring event handlers?
- A. They are common filters applied simultaneously to all event handlers.
- B. They limit which logs are checked for matches by the other filters.
- C. They can filter the logs before they are processed by FortiAnalyzer
- D. They download new filters to be used in event handlers.
Answer: D
NEW QUESTION # 108
Refer to the exhibit.
Based on the output, what can you conclude about the FortiAnalyzer logging status?
- A. The connection between FortiGate and FortiAnalyzer is overloaded.
- B. FortiGate is configured to send logs in batches.
- C. FortiGate is sending logs again after it performed a reboot.
- D. FortiGate has logs to send, but FortiAnalyzer is unavailable.
Answer: D
Explanation:
The output shows that FortiGate has sent a large number of logs (sent=180189698), but some logs have failed to be sent (failed=4507). This suggests that FortiAnalyzer was temporarily unavailable or had an issue receiving logs, leading to the failure count. There are no logs cached or dropped, indicating FortiGate is still attempting to send logs but with some failures.
NEW QUESTION # 109
View the exhibit.
What does the data point at 14:35 tell you?
- A. FortiAnalyzer is indexing logs faster than logs are being received.
- B. FortiAnalyzer is dropping logs.
- C. The sqlplugind daemon is ahead in indexing by one log.
- D. FortiAnalyzer has temporarily stopped receiving logs so older logs' can be indexed.
Answer: A
Explanation:
https://docs.fortinet.com/document/fortianalyzer/6.2.5/administration-guide/47690/insert-rate-vs-receive-rate- widget
NEW QUESTION # 110
View the exhibit.
Why is the total quota less than the total system storage?
- A. 3.6% of the system storage is already being used.
- B. The oftpd process has not archived the logs yet
- C. The logfiled process is just estimating the total quota
- D. Some space is reserved for system use, such as storage of compression files, upload files, and temporary report files
Answer: D
Explanation:
https://docs.fortinet.com/document/fortianalyzer/6.2.5/administration-guide/368682/disk-space-allocation
NEW QUESTION # 111
Which two statements about high availability (HA) on FortiAnalyzer are true? (Choose two.)
- A. All devices in a FortiAnalyzer HA cluster must have the same available disk space.
- B. All devices in a FortiAnalyzer HA cluster must run in the same operation mode, either analyzer mode or collector mode.
- C. FortiAnalyzer HA supports synchronization of logs as well as some system and configuration settings.
- D. FortiAnalyzer HA active-passive mode can function without VRRP.
Answer: B,C
Explanation:
The two correct statements about high availability (HA) on FortiAnalyzer are:
FortiAnalyzer HA supports synchronization of logs as well as some system and configuration settings.
FortiAnalyzer HA synchronizes both logs and certain system configuration settings between the units in the cluster to ensure consistent operation.
All devices in a FortiAnalyzer HA cluster must run in the same operation mode, either analyzer mode or collector mode.
In an HA cluster, all devices must be configured to operat` e in the same mode - either analyzer mode or collector mode-to ensure consistency and proper functionality across the cluster.
The other options, such as VRRP, are not required for HA in FortiAnalyzer, and disk space can vary between nodes but may impact log storage capacity.
NEW QUESTION # 112
What are offline logs on FortiAnalyzer?
- A. Logs that are collected from offline devices after they boot up.
- B. Logs that are indexed and stored in the SQL database.
- C. When you restart FortiAnalyzer. all stored logs are considered to be offline logs.
- D. Compressed logs, which are also known as archive logs, are considered to be offline logs.
Answer: D
Explanation:
Reference: https://help.fortinet.com/fa/faz50hlp/56/5-6-6/Content/FortiAnalyzer_Admin_Guide
/0300_Key_concepts/0600_Log_Storage/0400_Archive_analytics_logs.htm
Logs are received and saved in a log file on the FortiAnalyzer disks. Eventually, when the log file reaches a configured size, or at a set schedule, it is rolled over by being renamed. These files (rolled or otherwise) are known as archive logs and are considered offline so they don't offer immediate analytic support. Combined, they count toward the archive quota and retention limits, and they are deleted based on the ADOM data policy. FortiAnalyzer_7.0_Study_Guide-Online page 140
NEW QUESTION # 113
Which two settings must you configure on FortiAnalyzer to allow non-local administrators to authenticate to FortiAnalyzer with any user account in a single LDAP group? (Choose two.)
- A. An administrator group
- B. A trusted host profile that restricts access to the LDAP group
- C. A remote LDAP server
- D. A local wildcard administrator account
Answer: C,D
Explanation:
Reference: https://kb.fortinet.com/kb/documentLink.do?externalID=FD38567
NEW QUESTION # 114
How can you configure FortiAnalyzer to permit administrator logins from only specific locations?
- A. Use secure protocols
- B. Use static routes
- C. Use administrative profiles
- D. Use trusted hosts
Answer: D
Explanation:
https://docs.fortinet.com/document/fortianalyzer/6.2.5/administration-guide/186508/trusted-hosts
NEW QUESTION # 115
FortiAnalyzer centralizes which functions? (Choose three)
- A. Vulnerability assessment
- B. Security log analysis / forensics
- C. Graphical reporting
- D. Network analysis
- E. Content archiving / data mining
Answer: B,C,E
NEW QUESTION # 116
An administrator has configured the following settings:
What is the purpose of executing these commands?
- A. To encrypt log transfer between FortiAnalyzer and other devices.
- B. To create the secure channel used by the OFTP process.
- C. To record the hash value and authentication code of log files.
- D. To verify the integrity of the log files received.
Answer: D
Explanation:
The purpose of executing the provided CLI commands, which include setting the log-checksum to md5- auth, is to ensure the integrity of the log files. This setting is used to record the MD5 hash value of log files, which is a widely used cryptographic hash function that produces a 128-bit (16-byte) hash value. By using MD5 authentication, FortiAnalyzer ensures that the log files have not been altered or tampered with during transit, thereby verifying their integrity upon receipt. This is not related to encrypting log transfers, scheduling reports, or creating secure channels for OFTP (Over-the-FortiGate Protocol) processes.
NEW QUESTION # 117
The connection status of a new device on FortiAnalyzer is listed as Unauthorized.
What does that status mean?
- A. It is a device that has not yet been assigned an ADOM.
- B. It is a device whose registration has not yet been accepted in FortiAnalvzer.
- C. It is a device that FortiAnalvzer does not support.
- D. It is a device that is waiting for you to configure a pre-shared key.
Answer: B
Explanation:
The "Unauthorized" status indicates that the device has been discovered or attempted to connect but has not yet been authorized for management by FortiAnalyzer. It requires an administrator to approve or authorize the device before it can be fully managed.
NEW QUESTION # 118
An administrator, fortinet, can view logs and perform device management tasks, such as adding and removing registered devices. However, administrator fortinet is not able to create a mail server that can be used to send alert emails.
What can be the problem?
- A. ADOM mode is configured with Advanced mode.
- B. fortinet is assigned Restricted_User administrative profile.
- C. A trusted host is configured.
- D. fortinet is assigned the Standard_User administrative profile.
Answer: D
Explanation:
Administrator Fornetet is able to view logs and perform device management tasks such as adding and removing registered devices, but cannot create a mail server to send alert mails. The causes of this problem are:
fortinet is assigned a Restricted_User administrative rights profile.
Administrators who are assigned as Restricted_User have restricted access, which may include viewing logs and performing certain device management tasks, but not more advanced administrative functions such as configuring mail servers. Such permission restrictions prevent them from performing configuration changes that require higher permissions.
NEW QUESTION # 119
What is the recommended method of expanding disk space on a FortiAnalyzer VM?
- A. From the VM host manager, expand the size of the existing virtual disk and use the # execute format disk command to reformat the disk
- B. From the VM host manager, add an additional virtual disk and rebuild your RAID array
- C. From the VM host manager, add an additional virtual disk and use the #execute lvm extend <disk number> command to expand the storage
- D. From the VM host manager, expand the size of the existing virtual disk
Answer: C
Explanation:
https://kb.fortinet.com/kb/documentLink.do?externalID=FD40848
NEW QUESTION # 120
Refer to the exhibit.
What is the purpose of using the Chart Builder feature on FortiAnalyzer?
- A. To add charts directly to generate reports in the current ADOM
- B. To build a chart automatically based on the top 100 log entries
- C. To add a new chart under FortiView to be used in new reports
- D. To build a dataset and chart automatically, based on the filtered search results
Answer: A
NEW QUESTION # 121
......
FCP_FAZ_AD-7.4 Cert Guide PDF 100% Cover Real Exam Questions: https://pdftorrent.dumpexams.com/FCP_FAZ_AD-7.4-vce-torrent.html